48k BTU Tri Zone Ductless Mini Split AC, Heat Pump: 12k-18k-18k, with Linesets

Description

Mini Ductless Split Air Conditioner 48000 BTU
48000 BTU INVERTER Tri Zone Mini Split AC
22.5 SEER Efficiency w/ Heat Pump Technology
With a 48000 BTU total Cool / Heat Capacity, the
Thermocore T323D-H248-12+18+18 ENERGY STAR mini split air conditioner
can cool or heat 3 separate zones of 12000, 18000, & 18000 BTU for a total coverage area of 2400 ft² (900 ft² x 2 + 600 ft²).  A 22.5 SEER coupled with Inverter technology provides the benefits of low operation temps down to -13F, rapid cooling / heating as well as maximum efficiency.
3 x 15ft Linesets Included
Features
Specifications
Installation Kit
Controls
Setup - Installation
Warranty
Shipping
Available Accessories
Technical Data:
System Includes:
48,000 BTU
INVERTER
Cooling Capacity
:
(12k + 18k + 18k)
48,000 BTU INVERTER Heat Capacity
:
(12k + 18k + 18k)
22.5 SEER - 10.3 HSPF - 10.9 EER
/ ENERGY STAR Qualified
*
Pre-Charged with ECO-Friendly R410A
1 Year Parts - 5 Year Compressor Warranty
View Details >
Indoor Unit - Air Handler
Outdoor Unit - Condenser of 36,000 BTUs
15ft Copper Refrigeration Linesets
Digital Multi-function LCD Remote Controls
Product and Installation Manual
>>>
** Rated Capacity of Condenser will be less than actual delivered capacity in above configuration. Rated Capacity is not the same as Maximum Capacity.
Click here
for Capacity Calculation Table. **
Top Line Features:
22.5 SEER - 10.3 HSPF
- ENERGY STAR
Most Energy Efficient Quad-Zone Series on Market
Dry-Mode removes moisture w/o affecting temperature
Cross Flow Technology reduces Noise Output
Compatible with over 5 Filtration Medias
Freon Leak Detection > Notification System
Low Ambient Temperature Operation (-13° F)
Two-direction Air vane Evenly Distributes Air
Restart IC: Settings restored Following Power Outage
Follow-Me Function tracks Remote Location
The particle filter or “pre-filter” removes dust and other air-borne pathogens before pushing the air through additional filtration medias and the refrigeration coil array.  This filter is washable and comes factory installed with every ductless air conditioner system.
The open channel construction of the 3M High Air Flow (HAF) filter offers low initial airflow resistance, while its unique microstructure and electrostatic charge provides effective particle capture and retention. This translates into fewer filter change outs and reduced coil cleaning.
CLICK TO PURCHASE >>>
The Vitamin C Filtration media releases Vitamin C into the air which softens skin and reduces stress among other therapeutic benefits.  A good choice for those wanting to add some invigoration to their indoor air environment.  Filter lasts over 2 years.
CLICK TO PURCHASE >>>
The anti-microbial effect of silver ionic technology kills allergy causing bacteria by destroying the inner configuration elements of the cell body. The nano-silver attached to the filter screen constantly releases silver ions which directly eliminates and prohibits bacteria from replicating.
CLICK TO PURCHASE >>>
Eliminates odors such as ammonia and deactivates harmful chemicals has such as formaldehyde.  By forming positive positions on the filter surface, Electrostatic Fiber traps small dust particles, smoke and pet dander to prevent allergic reactions and neutralize odor in the air.
CLICK TO PURCHASE >>>
12000 BTU Indoor Unit specs
CLICK FOR FULL SPEC SHEET
Model Number
T3-OS212-EW
Capacity
12000 BTU
Air Flow (Hi/M/Lo)
520/360/250 cfm
Power Supply
230 V / 60 Hz / 1Ph
Noise Output (Hi/M/Lo)
36.5/30/25 dBA
Liquid / Gas
1/4" x 1/2"
Weight
18.1 lbs
Dimensions (W x D x H)
31.6" × 7.45" × 11.7" in.
VIEW FULL AIR HANDLER SPECIFICATION SHEET >>>
18000 BTU Indoor Unit specs
CLICK FOR FULL SPEC SHEET
Model Number
T321S-H218-E
Capacity
18000 BTU
Air Flow (Hi/M/Lo)
710/560/440 cfm
Power Supply
230 V / 60 Hz / 1Ph
Noise Output (Hi/M/Lo)
47/40/31 dBA
Liquid / Gas
1/4" x 1/2"
Weight
35.5 lbs
Dimensions (W x D x H)
42.5" × 8.9" × 13.2" inches
VIEW FULL AIR HANDLER SPECIFICATION SHEET >>>
Outdoor Unit (condenser) specs
CLICK FOR FULL SPEC SHEET
Model Number
T323D-H248
Compressor Brand
MITSUBISHI / GMCC
Rated Capacity
36000 BTU
Maximum AH Capacity
48000 BTU
Air Flow
2355 CFM
Power Supply
230 V / 60 Hz / 1Ph
Input Power
2600W - 3800W
Max Fuse
45A
SEER
22.5
EER
10.9
HSPF4
10.3
Sound Level
65 dBA
Operating Temp Range
-13F - 122 F (cool and heat)
Refrigerant
R410A / 105oz Charge
Liquid / Gas
1/4" x 3/8" (4)
Max Lineset Length (1 zone)
98 ft
Max Lineset Length (all zones)
197 ft
Weight
156.3 lbs
Dimensions (W x D x H)
37.25 × 16.14 × 31.89 inches
VIEW FULL CONDENSER SPECIFICATION SHEET >>>
CLICK TO VIEW COMBINATION CALCULATION TABLE >>>
Install Kit Contents:
15 Feet Flared Copper Tubing
x 3
15 Feet Pipe Insulation
x 3
Drain Pipe (connected to Indoor)
Pre-Filter 'Particle' Filtration Media
x 3
Wall Bracket for Indoor Unit
x 3
Brass Adaptors
for Alternate lineset sizes
Installation and User Manuals
*** Extend included 15 foot lineset. Just .50 / additional foot***
contact us for details >
Does not Include Electrical Wire Harness -
Click here to purchase
WHAT IS DC INVERTER?
DC Inverter Air Conditioners are the ultimate cooling and heating technology of the HVAC field.  They are called "DC inverter" because the alternative current (AC) is converted to Direct Current (DC) then, direct current inverted back to Alternative current with desired frequency. As known, the current supplied through the wall outlet has fixed frequency which is 60 Hertz. Different frequencies supplied to the compressor will result different running speeds of the compressor.  YMGI Inverter control systems use Pulse Amplitude Modulation (PAM) that is the most advanced and energy efficient method of inverting the current.  DC Inverter air conditioners bear special compressors that their speed could be changed by increasing or decreasing the frequency of the supplied power.  Therefore, unlike conventional split Air Contioners/Heat Pumps which cycle between on and off repeatedly, the DC Inverter control system will monitor the room temperature and adjust the compressor speed automatically.
Conventional compressors turn on and off to maintain the room temperature at desired level.  This will result compressor to draw tremendous energy each time it starts up. This will also reduce the life-span of the compressor and other components that are turning on and off.  Once a conventional system is running, it runs at its maximum speed, consuming the maximum amount of energy in order to produce the maximum of cooling or heating to maintain the desired temperature.  The system will then cycle between on and off in an effort to maintain this temperature. When a DC Inverter compressor initially starts up, it runs with a higher speed to bring the room temperature to desired level rapidly. Once the set temperature is reached, it slows down and adjust its capacity to counter the heat loss or heat gain of the building. By this way it will maintain a constant temperature.
BASIC OVERVIEW:
The indoor unit is hung like a picture frame approximately 6 - 8 feet above the floor usually on an exterior wall. A 2-3 inch hole must be made behind the indoor unit in the exterior wall to run the refrigerant copper tubing, electrical wires to the outside unit. Electrical Cables are NOT INCLUDED.
Click for supplies page.
The condensing unit comes pre-charged with R410A Freon however, procedures such as conducting leak tests etc. are still important steps in ensuring proper functioning of a split AC. *Although installation may seem easy to some, certain tools and experience is necessary to complete setup of a mini split*
Click for Installation Tip.
It is highly advised a certified HVAC technician complete installation to be eligible for warranty.
See warranty details below >
*5 Year Compressor - 1 Year on all other Parts*
Registration card will be sent with unit, this card should be completed by an HVAC technician (installer).  Installation of a mini split must be completed by a licensed HVAC (Heating, ventilating, & air conditioning) company to ensure any issues encountered in the future are not due to improper installation / workmanship.  Even though mini split setup is below the expertise requirements of central AC systems, these are not "plug-n-play" units that can be properly installed without certain tools any prior HVAC - electrical knowledge.   The installation includes electrical, gas, and refrigerant connections and generally regulated by a multiple sets of laws, codes and guidelines, at the federal, state and local levels. The failure to properly install HVAC equipment can raise personal safety and performance concerns. Warranty service - troubleshooting is provided through the contractor / installer and will be upheld as long as policies are observed.  Once a non-defective unit is installed by a HVAC company, chances of anything going wrong are very slim and almost all contractors will guarantee there workmanship and provide future service free of charge (installation warranty).  If it was determined that the unit is not functioning due to a defect and needs to be replaced, the part will be sent free of charge up to 1 year from date of purchase or 5 years for the compressor. If you receive a damaged or defective product, a replacement unit will be sent out Free of cost.  Damaged / Defective product will be picked up and brand new exchange will be shipped out.
SHIPS TO TO BOTH UNITED STATES AND CANADIAN LOCATIONS!
Our Thermocore systems ship via
RL Carriers
or similar LTL freight service out of Warren, Michigan and are palletized onto a single skid.  Transit time is usually between 4 to 6 business days from payment receipt depending on where you are geographically located.
Please provide a contact phone# upon checkout
(to be used for delivery purposes only).  SOMEBODY MUST BE ON SITE TO ACCEPT / SIGN FOR Order.  Failure to provide valid contact# will delay order.  System comes with Free shipping - this includes delivery to any location within the Continental United States. We will ship to Canadian locations but we need to quote separately - please contact our offices.  Additional freight for Canadian registries is usually around 0. (import and duties may apply).
Condenser Ground Stand
- Provides Flat even surface
- Avoids debris obstruction
Price:
.00
Click for more Info
Lineset
- Required for Installation
25ft - 30ft - 40ft - 50ft
Lengths
Price:
.00 > 4.00
Click for more Info
Condenser Bracket
- Mount your condenser at any height on an outdoor sidewall
Price:
.00
Click for more Info
Micro-Pump II
- Required when mounting air handler on Interior wall
Price:
2.00
Click for more Info
Electrical Wire Harness
- 16/4 Electrical Wire Harness
- For Extending Evap. Length
Price:
.15 / ft
Click for more Info
Additional Remote Controls
- Spare remote controls for the T3 Series Ductless System
Price:
.00
Click for more Info
Filter Medias
- Inserts into Filter Screen Slot
- Choice of 4 Filtration Medias
Price:
.00 - .00
Click for more Info
Wired Thermostat
- Permanently Hard Mounts
- Controls Settings w/ Remote
Price:
.00
Click for more Info
Swap 1- 12k Mount for Cassette:
(+) 0
Swap 1- 18k Mount for Cassette:
(+) 0
Swap 1-12k Mount for Suspended Ceiling:
(+) 0
Swap 1-18k Mount for Suspended Ceiling:
(+) 0
*If alternate air handler types are preferred,
contact us
and request invoice with preferred options. Availability fluctuates.
Customize your system to meet your requirements - see below table for available output options:
Dual-Zone Setup
12k + 18k
9k + 24k
18k + 18k
12k + 24k
Tri-Zone Setup
9k + 18k + 18k
12k + 12k + 18k
12k + 18k + 18k
18k + 18k + 18k
12k + 12k + 24k
09k + 09k + 24k
Quad-Zone Setup
9k + 9k + 9k + 9k
9k + 9k + 9k + 12k
9k + 9k + 12k + 12k
9k + 12k + 12k + 12k
9k + 9k + 9k + 18k
9k + 9k + 12k + 18k
12k + 12k + 12k + 12k
/
/
This system available in multiple air handler (zone) capacity combinations to meet the requirements of any application.  Air handlers are available in 9k, 12k and 18k outputs. Be advised, for arrangements where combined output of all heads exceeds rated capacity of condenser (36000 BTU's) - the total output will not exceed 36000's when all air handlers are running at full capacity simultaneously.  However, overated zones will draw required capacity from other zones either running at lower modes or areas that have reached thermostat settings to obtain rated output.  For example, with a 12k-12k-12k-12k configuration, the total output will be along the lines of 10k-10k-10k-10k when all zones are running on high/full settings at the same time.  However, once a zone obtains set temperature and/or operates at a lower setting, the capacity will bleed off into zone that needs the extra push to obtain the 12k-12k-12k-12k yield.
View the Mini Split FAQ >
View the Mini Split Outline Diagram >
Click to contact us >